JVC GY-HM790U, Инструкция по эксплуатации

Страница: 95 / 144

91
* Default values are indicated in bold characters.
Item Setting Values Function
TC/UB On
Off
For specifying whether to display the time code/user’s bit rate in the status display on the LCD
monitor and viewfinder screens.
On
: Displays the time code or user’s bit rate. Whether time code or user’s bit rate is
displayed is determined by the setting of the [TC DISPLAY] switch on the inner
panel of the camera recorder’s LCD monitor.
Off : Hides the time code or user’s bit rate.
Audio Meter On
Off
For specifying whether to display the audio level meter in the status display on the LCD monitor
and viewfinder screens.
On
: Displays the audio level meter.
Off : Hides the audio level meter.
Battery Info Time
Capacity%
Voltage
For setting the battery information to be displayed on the status screen when an AntonBauer or
IDX battery that supports communication is loaded.
The status screen is displayed on the LCD monitor and/or viewfinder.
The battery information appears only on the STATUS 1 screen in Camera mode. (
A Page 104)
Time : Displays the remaining battery power in minutes.
A
min
B
Capacity% : Displays the remaining battery power in percentage.
A
%
B
Voltage : Displays the current battery voltage in units of 0.1 V.
A
V
B
Memo :
●
When a battery other than the one recommended (communication supported) is used,
A
Voltage
B
may sometimes be displayed even when
A
Time
B
or
A
Capacity%
B
is selected.
●
When
A
Time
B
or
A
Capacity%
B
is selected, the battery mark that appears before the value
changes according to the remaining battery power.
: 12 % and below, : 1 3 % - 29 %, : 3 0 % - 59 %, : 60 % - 100 %
●
Display changes to
A B
once the battery power falls below 12 %.
●
When calibration of the battery is re q uired,
A B
appears for 2 seconds after every 3 0
seconds of the voltage display.
●
CALIBRATION is a state that re q uires renewal of the battery power information. The battery is
able to function as usual without calibration. However, calibration is recommended as correct
information of the remaining power and time cannot be obtained otherwise. For more details,
refer to the instruction manual of the battery.
●
The remaining battery power and remaining time are intended as reference values for the
shooting duration.
●
When an IDX battery is loaded while the camera recorder is connected to a KA-MR100G
(Memory Recorder), the
A
Time
B
display setting may be disabled even when a recommended
battery (communication supported) is used.
Date Style DMY (E model)
MDY (U model)
YMD
For setting the date display se q uence in the status display on the LCD monitor and viewfinder
screens.
DMY
: Day/Month/Year
MDY : Month/Day/Year
YMD : Year/Month/Day
Time Style 24hour (E model)
12hour (U model)
For setting the time display in the status display on the LCD monitor and viewfinder screens.
24hour
: 24-hour display.
12hour : 12-hour display. (AM/PM)
Shutter Disp. DEG
SEC
For setting the shutter display in the status display on the LCD monitor and viewfinder screens.
DEG
: Displays the shutter speed in degrees in the same way as film cameras.
SEC : Displays the shutter speed in seconds.
Memo :
● A
DEG
B
is selectable only when [Frame & Bit Rate] is set to
A
24p (SP)
B
,
A
24p (HQ)
B
,
A
25p
(SP)
B
, or
A
25p (HQ)
B
. When [Frame & Bit Rate] is set to other values, the shutter display
setting is fixed at
A
SEC
B
and cannot be selected. ( A Page 75)
●
When a Remote Control Unit is connected, the shutter display setting is fixed at
A
SEC
B
regardless of the [Frame & Bit Rate] setting.
RES 2
RES
CAL