Juniper SSG 20-WLA Скачать руководство пользователя страница 45

Страница: 45 / 82

Mini PIM Configuration

set interface bri1/0 ppp profile isdnprofile
save

For more information on how to configure the ISDN interface, refer to the

Concepts

& Examples ScreenOS Reference Guide

To configure the ISDN interface as the backup interface, see “Backup Untrust
Interface Configuration” on page 26.

The T1 Interface

The T1 interface is a basic Physical Layer protocol used by the Digital Signal level 1
(DS-1) multiplexing method in North America. A T1 interface operates at a bit-rate
of 1.544 Mbps and can support 24 DS0 channels.

The devices support the following T1 DS-1 standards:

ANSI TI.107, TI.102

GR 499-core, GR 253-core

AT&T Pub 54014

ITU G.751, G.703

To configure the T1 mini PIM, do either of the following:

WebUI

Network > Interfaces > Edit (interface) > WAN: Enter or select the applicable
option value, click

WAN Configure: main link
WAN Encapsulation: cisco-hdlc
Zone Name: untrust
IP Address/Netmask 172.18.1.1/24

CLI

set interface serial1/0 encap cisco-hdlc
set interface serial1/0 ip 172.18.1.1/24

For information on how to configure the T1 interface, refer to the

Concepts &

Examples ScreenOS Reference Guide

Содержание SSG 20-WLA



















































































Результаты поиска

Содержание SSG 20-WLA

Отзывы:

Бренды по названию

Популярные бренды

Juniper SSG 20-WLA, Руководство по установке и настройке оборудования

Результаты поиска

Содержание SSG 20-WLA

Отзывы:

Бренды по названию

Популярные бренды