Juniper QFX5120 Series Скачать руководство пользователя

Страница: 204 / 207

•

AS/NZS CISPR 32:2015 Australia/New Zealand Radiated and Conducted Emissions

•

FCC 47 CFR Part 15 USA Radiated and Conducted Emissions

•

IC ICES-003 Canada Radiated and Conducted Emissions

•

VCCI-CISPR 32:2016 Japanese Radiated and Conducted Emissions

•

BSMI CNS 13438 Taiwan Radiated and Conducted Emissions (at 10 Meter)

•

KN 32 and KN 35 Korea Radiated Emission and Immunity Characteristics (at 10 Meter)

•

KN 61000 Korea Immunity Test

•

TEC/SD/DD/EMC-221/05/OCT-16 (Supersedes No. TEC/EMI/TEL-001/01/FEB-09) India EMC standard

•

Juniper Inductive GND (JIG)

Canada

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

The Industry Canada label identifies certified equipment. This certification means that the equipment

meets certain telecommunications network protective, operational, and safety requirements. Industry

Canada does not guarantee the equipment will operate to the users’ satisfaction.

Before installing this equipment, users should ensure that it is permissible to connect the equipment to

the facilities of the local telecommunications company. The equipment must also be installed using an

acceptable method of connection. In some cases, the inside wiring associated with a single line individual

service may be extended by means of a certified connector assembly. The customer should be aware that

compliance with the above conditions may not prevent degradation of service in some situations.

Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated

by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions,

may give the telecommunications company cause to request the user to disconnect the equipment.

CAUTION:

Users should not attempt to make electrical ground connections by themselves,

but should contact the appropriate inspection authority or an electrician, as appropriate.

Users should ensure for their own protection that the electrical ground connections of the power utility,

telephone lines, and internal metallic water pipe system, if present, are connected together. This precaution

may be particularly important in rural areas.

210

Содержание QFX5120 Series
















































































































































































































Результаты поиска

Содержание QFX5120 Series

Отзывы:

Похожие инструкции для QFX5120 Series

Бренды по названию

Популярные бренды

Juniper QFX5120 Series, Руководство по оборудованию

Результаты поиска

Содержание QFX5120 Series

Отзывы:

Похожие инструкции для QFX5120 Series

Бренды по названию

Популярные бренды