Juniper QFX5120 Series Скачать руководство пользователя

Страница: 187 / 207

AC Power Electrical Safety Guidelines

CAUTION:

For devices with AC power supplies, an external surge protective device

(SPD) must be used at the AC power source.

The following electrical safety guidelines apply to AC-powered devices:

•

Note the following warnings printed on the device:

“CAUTION: THIS UNIT HAS MORE THAN ONE POWER SUPPLY CORD. DISCONNECT ALL POWER

SUPPLY CORDS BEFORE SERVICING TO AVOID ELECTRIC SHOCK.”

“ATTENTION: CET APPAREIL COMPORTE PLUS D'UN CORDON D'ALIMENTATION. AFIN DE

PRÉVENIR LES CHOCS ÉLECTRIQUES, DÉBRANCHER TOUT CORDON D'ALIMENTATION AVANT

DE FAIRE LE DÉPANNAGE.”

•

AC-powered devices are shipped with a three-wire electrical cord with a grounding-type plug that fits

only a grounding-type power outlet. Do not circumvent this safety feature. Equipment grounding must

comply with local and national electrical codes.

•

You must provide an external certified circuit breaker (2-pole circuit breaker or 4-pole circuit breaker

based on your device) rated minimum 20 A in the building installation.

•

The power cord serves as the main disconnecting device for the AC-powered device. The socket outlet

must be near the AC-powered device and be easily accessible.

•

For devices that have more than one power supply connection, you must ensure that all power

connections are fully disconnected so that power to the device is completely removed to prevent electric

shock. To disconnect power, unplug all power cords (one for each power supply).

Power Cable Warning (Japanese)

WARNING:

The attached power cable is only for this product. Do not use the cable for another product.

193

Содержание QFX5120 Series
















































































































































































































Результаты поиска

Содержание QFX5120 Series

Отзывы:

Похожие инструкции для QFX5120 Series

Бренды по названию

Популярные бренды

Juniper QFX5120 Series, Руководство по оборудованию

Результаты поиска

Содержание QFX5120 Series

Отзывы:

Похожие инструкции для QFX5120 Series

Бренды по названию

Популярные бренды