Juniper QFX5120 Series Скачать руководство пользователя

Страница: 161 / 207

Installation Instructions Warning

WARNING:

Read the installation instructions before you connect the device to a power

source.

Waarschuwing Raadpleeg de installatie-aanwijzingen voordat u het systeem met de

voeding verbindt.

Varoitus Lue asennusohjeet ennen järjestelmän yhdistämistä virtalähteeseen.

Attention Avant de brancher le système sur la source d'alimentation, consulter les

directives d'installation.

Warnung Lesen Sie die Installationsanweisungen, bevor Sie das System an die Stromquelle

anschließen.

Avvertenza Consultare le istruzioni di installazione prima di collegare il sistema

all'alimentatore.

Advarsel Les installasjonsinstruksjonene før systemet kobles til strømkilden.

Aviso Leia as instruções de instalação antes de ligar o sistema à sua fonte de energia.

¡Atención! Ver las instrucciones de instalación antes de conectar el sistema a la red de

alimentación.

Varning! Läs installationsanvisningarna innan du kopplar systemet till dess

strömförsörjningsenhet.

Chassis and Component Lifting Guidelines

•

Before moving the device to a site, ensure that the site meets the power, environmental, and clearance

requirements.

•

Before lifting or moving the device, disconnect all external cables and wires.

•

As when lifting any heavy object, ensure that most of the weight is borne by your legs rather than your

back. Keep your knees bent and your back relatively straight. Do not twist your body as you lift. Balance

the load evenly and be sure that your footing is firm.

•

Use the following lifting guidelines to lift devices and components:

167

Содержание QFX5120 Series
















































































































































































































Результаты поиска

Содержание QFX5120 Series

Отзывы:

Похожие инструкции для QFX5120 Series

Бренды по названию

Популярные бренды

Juniper QFX5120 Series, Руководство по оборудованию

Результаты поиска

Содержание QFX5120 Series

Отзывы:

Похожие инструкции для QFX5120 Series

Бренды по названию

Популярные бренды