Juniper MX2010 Скачать руководство пользователя страница 46

Страница: 46 / 825

Line Cards Supported on MX Series Routers

IN THIS SECTION

FPCs and PICs | 21

DPCs | 21

MPCs and MICs | 22

Switch Fabric Boards (SFB, SFB2, SFB3) | 22

Switch Control Boards | 23

MX2000 ADC | 23

Routing Engines and CB-REs | 23

Juniper Networks MX Series 5G Universal Routing Platforms process incoming and outgoing packets using:

Switch Control Board

(SCB, SCBE, SCBE2,

SCBE3)

Modular Port

Concentrator

(MPC) with a

Modular Interface

Card (MIC)

Flexible PIC

Concentrator

(FPC) with

Physical Interface

Card (PIC)

Dense Port

Concentrator (DPC)

•

House the routing

engine

•

Control power to

MPCs

•

Monitor and control

system functions

such as fan speed

and the system front

panel

•

Manage clocking,

resets, and boots

Provides physical

interfaces for

MX2000 series

routers.

Provides physical

interfaces for

MX240, MX480,

and MX960 routers.

Provides multiple

physical interfaces

and Packet

Forwarding Engines

(PFEs) on a single

board that installs into

a slot within the

MX240, MX480, and

MX960 routers.

Description

—

Maximum Supported

on MX2020

—

Maximum Supported

on MX2010

Содержание MX2010


























































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX2010

Отзывы:

Похожие инструкции для MX2010

Бренды по названию

Популярные бренды

Juniper MX2010, Руководство по оборудованию

Результаты поиска

Содержание MX2010

Отзывы:

Похожие инструкции для MX2010

Бренды по названию

Популярные бренды