Juniper EX9204 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 11

Juniper EX9204 Скачать руководство пользователя страница 9

[edit]

root@# set interfaces fxp0 unit 0 family inet address address/prefix-length

8. Configure the IP address of a DNS server.

[edit]

root@# set system name-server address

9. (Optional) Configure the static routes to remote subnets with access to the management port.

[edit]

root@# set routing-options static route remote-subnet next-hop destination-IP retain no-readvertise

10. Configure the telnet service at the [edit system services] hierarchy level.

[edit]

root@# set system services telnet

11. (Optional) Configure additional properties by adding the necessary configuration statements.

12. Commit the configuration and exit the configuration mode.

NOTE:

To reinstall Junos OS, boot the switch from the removable media. Do not insert the removable media

during normal operations. The switch does not operate normally when it is booted from the removable media.

Step 3: Keep Going

IN THIS SECTION

Safety Warnings Summary | 10

Power Cable Warning (Japanese) | 11

Contacting Juniper Networks | 11

9

«
...
7
8
9
10
11
»

Содержание EX9204












Отзывы:

Нет отзывов