Jungheinrich ETX 513 страница 55 Скачать руководство пользователя | Manualshive

Страница: 55 / 408

background image

C Transport and Commissioning

1

Transport

The truck can be transported in two different ways, depending on the height of the
mast and the local conditions.

– Vertically with the mast and load handler assembled

(for low heights)

– Vertically with the mast and load handler disassembled

(for large truck heights).
All hydraulic lines between the basic truck and mast are disconnected for
transportation.

Safety Instructions for Assembly and Commissioning

WARNING!

Incorrect assembly can result in accidents

The assembly of the truck at the application site, commissioning and driver training
must only be performed by the manufacturer's customer service representatives who
have been specially trained for these tasks.

u

The hydraulic and electrical lines may only be connected to the basic truck / mast
interface when the mast has been properly assembled.

u

The truck can then be started.

u

If several trucks have been delivered, make sure that always the serial numbers of
the load handlers, masts and basic trucks match each other.

53

04.19 en-GB

«
...
53
54
55
56
57
...
»

Содержание ETX 513

























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ETX 513

Бренд: Sealey Страницы: 2

Бренд: Daewoo Страницы: 83

Бренд: Lift-Rite Страницы: 20

Бренд: Lift-Rite Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды