Jungheinrich ETX 513 Скачать руководство пользователя | Manualshive

Страница: 44 / 408

background image

4.6

Engine Data

Description

ETX 513 / ETX 515

Drive motor, output at S

2

60 min

7,6 kW

Lift motor, output for S

3

25 %

21 kW

Steer motor, output at 2200 rpm and S

3

= 15 %

1 kW

4.7

EN norms

Noise emission level

– ETX 513: 65 dB(A)
– ETX 515: 65 dB(A)

in accordance with EN 12053 as harmonised with ISO 4871.

Z

The noise emission level is calculated in accordance with standard procedures and
takes into account the noise level when travelling, lifting and when idle. The noise
level is measured at the level of the driver's ear.

Vibration

Weighted vibration acceleration on seat:
– ETX 513: aw,zS = 0,56 m/s²
– ETX 515: aw,zS = 0,56 m/s²

in accordance with EN 13059.

Seat cushioning:
– ETX 513: 64,8 %
– ETX 515: 64,8 %

in accordance with EN 13059.

Z

The internal accuracy of the measuring chain for at 21°C at ± 0,02 m/s². Further
deviations may occur in particular through the positioning of the sensor and different
driver weights.

Z

The  vibration  acceleration  acting  on  the  body  in  the  operating  position  is,  in
accordance with standard procedures, the linearly integrated, weighted acceleration
in  the  vertical  direction.  It  is  calculated  when  travelling  over  bumps  at  constant
speed. These recordings were taken on a single occasion and must not be confused
with  the  human  vibrations  of  the  "2002/44/EC/Vibrations"  operator  directive.  The
manufacturer  offers  a  special  service  to  measure  these  human  vibrations,  see
page 357.

Electromagnetic compatibility (EMC)

The  manufacturer  confirms  that  the  truck  adheres  to  the  limits  for  electromagnetic
emissions  and  resistance  as  well  as  the  static  electricity  discharge  test  in
accordance  with  EN  12895  as  well  as  the  standardised  instructions  contained
therein.

42

04.19 en-GB

«
...
42
43
44
45
46
...
»

Содержание ETX 513

























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ETX 513

Бренд: Yale Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды