manualshive.com logo in svg

Jungheinrich ETX 513, Руководство по эксплуатации

Поделиться
Скачать
Jungheinrich ETX 513 Скачать руководство пользователя страница 278

8.8

Horizontal positioning (

o

)

Your  truck  may  optionally  be  equipped  with  the  “Horizontal  Positioning  (HozPos)”
function. This function supports the owner in positioning (automatic, direct targeted
positioning of the pallet location) the truck in the rack and at the transfer station. In
conjunction  with  the  integrated  rack  height  select,  this  provides  for  consistent
stopping and load collecting in the rack and at transfer stations with minor, monitored
deviations. The positioning accuracy is ± 10 mm vertically and ± 30 mmhorizontally.

"Horizontal  Positioning  (HozPos)"  offers  programmable  warehouse  conditions.  The
setting is made by the manufacturer's customer service department.

To achieve constant insertion widths over the entire lift height, ten height-dependent
traverse adjustment values can be programmed as an option.

The aisle and fork positions are checked on entry to the aisle.

Options
– Manual entry of destination via cursor keys and numerical keypad
– Entry of destination via barcode scanner on the control panel or load handler
– Destination entry via radio connection
– Type of stacking operation, see page 269
– Extension lock during travel without target or incorrect target

Z

Maintenance  intervals  are  specified  in  the  section  Maintenance,  Inspection  and 
Changing of Maintenance Parts Requiring Replacement, see page 359.

276

04.19 en-GB

Содержание ETX 513

























































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды