manualshive.com logo in svg

Jungheinrich ETX 513, Руководство по эксплуатации

Поделиться
Скачать
Jungheinrich ETX 513 Скачать руководство пользователя страница 236

7.2

Functional description

– Mobile personal protection system with laser scanner based obstacle detection.
– Apron field protection.
– Optimum integration in the truck.
– Easy adjustment / settings to match warehouse environment.
– Automatic  speed  reduction  /  stopping  in  front  of  obstacles  /  personnel  /  other

industrial trucks.

7.2.1

Standard functions

– Crawl speed released when scanner covered (load handler lowered).
– Crawl  speed  released  when  approaching  the  last  pallet  location  at  a  closed

narrow aisle end.

– Automatic reduction of maximum speed to 2,5 km/h before exiting the aisle.
– Additional stop at aisle end; optionally temporary, confirmed or absolute.
– Short  range  apron  field  protection  (directly  in  front  of  and  behind  the  truck  –

depending on travel direction).

– Lower cutout for protection field infringement.

WARNING!

The Personal Protection System does not provide collision protection in accordance
with DIN 15185 Part 2 Section 3.7.

234

04.19 en-GB

Содержание ETX 513

























































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды