manualshive.com logo in svg

Jungheinrich ETX 513, Руководство по эксплуатации

Поделиться
Скачать
Jungheinrich ETX 513 Скачать руководство пользователя страница 235

7

Personal safety system (

o

)

7.1

Personal Protection System (PPS)

The  truck's  integrated  personal  protection  system  (PSS)  is  designed  to  protect
persons.  The  Personal  Protection  System  (PSS)  is  used  with  industrial  trucks  in
warehouse  systems  where  pedestrians  are  not  permitted  to  be  in  narrow  aisles  at

the same time as industrial trucks.

Z

The  Personal  Protection  System  meets  the  requirements  of  BGV  D  27,  §28
paragraph  2  and  DIN  15185,  Part  2  section  3.13.  The  Personal  Protection  System
complies with ISO 13849 PXF Level D for detection of persons and obstacles. The
safety laser scanner corresponds to laser protection class 1. No other measures for
screening the laser beam are required (eye protection).
The laser scanner meets the requirements of standards CDRH 21,CFR 1030.10 and
DIN EN 60825:2001.

WARNING!

Caution  –  exposure  to  hazardous  radiation  can  result  if  the  operating  or  adjusting
devices  used  or  procedures  carried  out  differ  from  those  stated  in  the  above
standards and directives.

National / international regulations apply to the assembly and use of the safety laser
scanner both for commissioning and recurrent technical inspections, in particular:
– Machinery Directive 2006/42/EG
– Use of Work Equipment Directive 89/655/EWG
– Accident prevention / health and safety regulations
– other relevant safety regulations

Z

The manufacturer and operators of the machine on which the safety laser scanner is
being  used  are  responsible  for  agreeing  and  complying  with  all  valid  safety
regulations issued by the relevant authorities.

233

04.19 en-GB

Содержание ETX 513

























































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды