manualshive.com logo in svg

Jungheinrich ETX 513, Руководство по эксплуатации

Поделиться
Скачать
Jungheinrich ETX 513 Скачать руководство пользователя страница 170

4.13

Lifting / lowering – outside and inside narrow aisles

4.13.1

Main Lift raise/lower

WARNING!

Accident risk when lifting and lowering

Other people can be injured in the truck's hazardous area.
The hazardous area is defined as the area in which people are at risk from the truck
movement, the load handler, attachments etc. This also includes areas which can be
reached by falling loads or lowering operating equipment.
Apart from the operator (in the normal operating position) there should be no other
people in the truck's hazardous area.

u

Instruct other people to move out of the hazardous area of the truck. Stop working
with the truck if people do not leave the hazardous area.

u

If people do not leave the hazardous area despite the warning, prevent the truck
from being used by unauthorised people.

u

Only  carry  loads  that  have  been  secured  and  positioned  in  accordance  with
regulations.  Use  suitable  precautions  to  prevent  parts  of  the  load  from  tipping  or
falling down.

u

Damaged loads must not be transported.

u

Do not exceed the maximum loads specified on the capacity plate.

u

Do not stand underneath a raised load handler.

u

Do not stand on the load handler.

u

Do not lift other people on the load handler.

u

Do not reach or climb into moving truck parts.

u

The operator must not leave the operator position when the load handler is raised.

u

Do not climb onto parts of the building or other trucks.

168

04.19 en-GB

Содержание ETX 513

























































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды