Jungheinrich ETX 513 страница 158 Скачать руководство пользователя | Manualshive

Страница: 158 / 408

background image

4.11

Negotiating narrow aisles

4.11.1

Negotiating narrow aisle with rail-guided trucks (

o

)

WARNING!

Unauthorised entry of narrow aisles by other trucks or people can cause
accidents

Unauthorised personnel must not enter narrow aisles (truck lanes in racking systems
with safety distances < 500 mm), nor must any personnel cross through them. These
work areas must be marked and identified accordingly.

u

Carry out a daily inspection of the safety mechanisms on the truck or the racking
system to avoid hazards and to protect personnel.

u

These must not be rendered ineffective, misused, adjusted or removed.

u

Report any defects to your supervisor immediately.

u

Tag out and decommission a faulty lift truck.

u

Only return the truck to service when you have identified and rectified the fault.

u

Tag out faulty racking systems and block them for entry.

u

Only return the truck to service when you have identified and rectified the fault.

u

Note DIN 15185 Part 2.

u

Narrow aisles must only be entered by trucks which are designated for this
purpose.

u

Before entering a narrow aisle, the driver must look for people or other trucks in
the aisle. Never enter an aisle where there are people or other trucks. If there are
people or trucks in the aisle, stop the truck immediately.

156

04.19 en-GB

«
...
156
157
158
159
160
...
»

Содержание ETX 513

























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ETX 513

Stack-N-Go FPS3000-43NFO-21

Бренд: Southworth Страницы: 36

Stack-N-Go FPS3000-43NAS

Бренд: Southworth Страницы: 37

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды