Jungheinrich ESD 220 Скачать руководство пользователя

Страница: 110 / 186

8.4.7

Delete individual user codes

Requirements

– To prepare the truck for operation, see page 101.

Procedure

• Press the O key (93).
• Enter the valid master code with the digit keys.

When you enter the valid master code the LED
(92) flashes green.

• Enter the parameters 0-0-3 with the digit keys.
• Confirm with the SET key (91).

The LEDs (89,92) flash green.

• Enter the user code to be deleted with the digit keys.
• Confirm with the SET key (91).

The LEDs (90,92) flash green.

• Enter the user code to be deleted again with the digit keys.
• Confirm with the SET key (91).

Wait until the LED (92) flashes green. The user code is now deleted.

• Press the O key (93).

The truck is switched off and the LED (92) is lit red.

• Check that the user code has been deleted:

• Switch the truck on with the user code to be deleted, see page 101

After entering the user code the LED (92) flashes red and the truck remains
switched off.

• Press the O key (93).

The truck remains switched off and the LED (92) is lit red.

108

10.19 en-GB

Содержание ESD 220



























































































































































































Результаты поиска

Содержание ESD 220

Отзывы:

Похожие инструкции для ESD 220

Бренды по названию

Популярные бренды

Jungheinrich ESD 220, Руководство по эксплуатации

Результаты поиска

Содержание ESD 220

Отзывы:

Похожие инструкции для ESD 220

Бренды по названию

Популярные бренды