Jungheinrich EJE 220 Скачать руководство пользователя страница 115

Страница: 115 / 232

7.3.7

Delete individual user codes

Requirements

– To prepare the truck for operation, see page 108.

Procedure

• Press the O key (69).
• Enter the valid master code with the digit keys.

When you enter the valid master code the LED
(68) flashes green.

• Enter the parameters 0-0-3 with the digit keys.
• Confirm with the SET key (67).

The LEDs (65,68) flash green.

• Enter the user code to be deleted with the digit keys.
• Confirm with the SET key (67).

The LEDs (66,68) flash green.

• Enter the user code to be deleted again with the digit keys.
• Confirm with the SET key (67).

Wait until the LED (68) flashes green. The user code is now deleted.

• Press the O key (69).

The truck is switched off and the LED (68) is lit red.

• Check that the user code has been deleted:

• Switch the truck on with the user code to be deleted, see page 108

After entering the user code the LED (68) flashes red and the truck remains
switched off.

• Press the O key (69).

The truck remains switched off and the LED (68) is lit red.

115

04.19 en-GB

Содержание EJE 220









































































































































































































































Результаты поиска

Содержание EJE 220

Отзывы:

Бренды по названию

Популярные бренды

Jungheinrich EJE 220, Руководство по эксплуатации

Результаты поиска

Содержание EJE 220

Отзывы:

Бренды по названию

Популярные бренды