Jung FMDW360WW Скачать руководство пользователя страница 1

eNet motion detector

eNet motion detector
Art. no.: FMDW360WW

Operating instructions

1

Safety instructions

Electrical devices may only be mounted and connected by electrically skilled persons.

Serious injuries, fire or property damage possible. Please read and follow manual fully.

The radio communication takes place via a non-exclusively available transmission path, and is
therefore not suitable for safety-related applications, such as emergency stop and emergency
call.

These instructions are an integral part of the product, and must remain with the end customer.

2

Battery safety instructions

This device or its accessories are supplied with batteries in the form of alkaline batteries LR03.

DANGER! Batteries can be swallowed. This can lead directly to death by suffocation.
Keep new and used batteries away from children.
Do not use devices if the battery compartment does not close securely and keep away from
children.
If you suspect that a battery has been swallowed or is in any orifice of the body, seek immediate
medical attention.

WARNING! Improper handling of batteries can result in explosion, fire or chemical burn due to
leakage.

Do not heat or throw batteries into fire.
Do not reverse polarity, short-circuit or recharge batteries.
Do not deform or disassemble batteries.
Replace batteries only with an identical or equivalent type.
Remove empty batteries immediately and dispose of in an environmentally friendly manner.
Exchange all batteries at the same time. Only use batteries of the same type and manufacturer.
Do not combine old and new batteries.

3

Intended use

Automatic switching of lighting depending on the heat motion and ambient brightness

Operation only with radio actuators for switching and dimming from the eNet system

Ceiling mounting, surface-mounted, in dry interiors

4

 Function

Product characteristics

LED for signalling

Battery-powered device

Brightness threshold settable

Run-on time adjustable

Sensitivity can be set

Can be set with eNet server:

Disabling of manual commissioning

Longer run-on time adjustable

Brightness threshold settable

Power saving level

1 / 12

82598403

25.07.2019

J0082598403

Содержание FMDW360WW













Отзывы: