JUMO TYA S202 Скачать руководство пользователя страница 94 | Manualshive

Страница: 94 / 99

JUMO TYA S202 Скачать руководство пользователя страница 94

10 Technical data

94

V1.00/EN/00709725 [Thyristor power controller TYA S202]

10.3.1Display and measuring accuracy

All specifications refer to the power controller nominal data.

10.4 Binary output (fault signal output master only)

10.5 General specifications

Current

0 (4) to 20 mA R

i

= 50

Ω

Voltage

0 (2) to 10 V R

i

= 25 k

Ω

0 (1) to 5 V R

i

= 25 k

Ω

Mains voltage: ±2.5 %

Load current: ±1 %

Load voltage:

±1 %

Analog input
Voltage/current: ±1 %

Relay (changeover contact)
without contact protection
circuit

30,000 switching operations at a switching capacity of AC 230 V / 3 A
(1.5 A), 50 Hz, B300 (UL 508)

Thyristor control:

Setpoint specification
current input
(can carry current up to 25 mA)

Setpoint specification
voltage input
(surge proof up to max. DC 32 V)

Via interface

Continuous

The power controller provides the power for the load continuously depending on the configured
setpoint specification.

Possible

Logic
(Solid state relay SSR)

The power controller acts like a switch and switches the load ON and OFF. The switching thresh-
old is always in the middle of the configured current/voltage range
At 4 to 20 mA, it is 12 mA; at 0 to 10 V, it is 5 V.

Possible

Circuit variants

- Three-phase economy circuit in master slave operation

Operating modes

- Burst-firing operation for resistive or transformer load

Load types

All resistive loads through to inductive loads are permitted.

In the case of transformer loads, the nominal induction of 1.2 tesla must not
be exceeded (value is 1.45 T in the case of mains overvoltage).

Special features

- Dual energy management
- Soft start with pulse groups

Electrical connection

For type 709066/X -0X-020...
Control and load leads are connected via screw terminals.
From type 709066/X -0X-032...
Control cables are connected via screw terminals and load leads via cable
lugs DIN 46235 and DIN 46234 or tubular cable lugs.

Operating conditions

The power controller is designed as a built-in device according to:
EN 50178,
pollution degree 2, overvoltage category Ü III

«
...
92
93
94
95
96
...
»

Содержание TYA S202




































































































Отзывы:

Нет отзывов