JUMO flowTRANS MAG H01 Скачать руководство пользователя страница 184

Страница: 184 / 260

13 Technical data

184

13.2.5

Maximum ambient temperature depending on the medium temperature

IMPORTANT (NOTE)!

There is the additional document "JUMO flowTRANS MAG S/H - Safety Manual Ex for devices 406012 -

406019" for the measuring systems that are used in potentially explosive areas.

The information and data contained in the document must also be strictly observed.

Compact design
Lining

Flange

Ambient temperature

Medium temperature

material

Minimum

Maximum

Minimum

Maximum

Hard rubber

Steel

-10 °C (14 °F)

60 °C (140 °F)

-10 °C (14 °F)

80 °C (176 °F)

For version "Sensor housing made of steel"

90 °C (194 °F)

Stainless steel -15 °C (5 °F)

60 °C (140 °F)

-15 °C (5 °F)

80 °C (176 °F)

90 °C (194 °F)

Soft rubber

Steel

-10 °C (14 °F)

60 °C (140 °F)

-10 °C (14 °F)

60 °C (140 °F)

Stainless steel -15 °C (5 °F)

60 °C (140 °F)

-15 °C (5 °F)

60 °C (140 °F)

PFA

Steel

-10 °C (14 °F)

60 °C (140 °F)

-10 °C (14 °F)

90 °C (194 °F)

PTFE

45 °C (113 °F)

130 °C (266 °F)

Thick PTFE

Stainless steel

-20 °C (-4 °F)

60 °C (140 °F)

-25 °C (-13 °F)

90 °C (194 °F)

ETFE

For version "Sensor housing made of aluminum (double shell housing)"

-40 °C (-40 °F)

for low temperature version (optional)

45 °C (113 °F)

130 °C (266 °F)

Ceramic
Carbide

Steel

-10 °C (14 °F)

60 °C (140 °F)

-10 °C (14 °F)

80 °C (176 °F)

45 °C (113 °F)

Stainless steel

-20 °C (-4 °F)

60 °C (140 °F)

-20 °C (-4 °F)

80 °C (176 °F)

45 °C (113 °F)

Compact design (high-temperature version)

For version "Sensor housing made of aluminum (double shell housing)"

Lining

Flange

Ambient temperature

Medium temperature

material

Minimum

Maximum

Minimum

Maximum

PFA
Thick PTFE

Steel

-10 °C (14 °F)

60 °C (140 °F)

-10 °C (14 °F)

180 °C (356 °F)

Stainless steel

-20 °C (-4 °F)

60 °C (140 °F)

-20 °C (-4 °F)

180 °C (356 °F)

-40 °C (-40 °F)

for low temperature version (optional)

ETFE

Steel

-10 °C (14 °F)

60 °C (140 °F)

-10 °C (14 °F)

130 °C
(266 °F)
130 °C
(266 °F)

Stainless steel

-20 °C (-4 °F)

60 °C (140 °F)

-20 °C (-4 °F)

-40 °C (-40 °F)

Содержание flowTRANS MAG H01





































































































































































































































































Результаты поиска

Содержание flowTRANS MAG H01

Отзывы:

Похожие инструкции для flowTRANS MAG H01

Бренды по названию

Популярные бренды

JUMO flowTRANS MAG H01, Руководство по эксплуатации

Результаты поиска

Содержание flowTRANS MAG H01

Отзывы:

Похожие инструкции для flowTRANS MAG H01

Бренды по названию

Популярные бренды