JUMO digiLine CR HT10 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 84

JUMO digiLine CR HT10 Скачать руководство пользователя страница 7

7

1 Safety information

1

Safety information

1.1

Safety signs

1.1.1

Warning symbols

DANGER!

This symbol indicates that

personal injury from electrocution

may occur if the appropriate precaution-

ary measures are not taken.

WARNING!

This symbol in connection with the signal word indicates that

personal injury

may occur if the respective

precautionary measures are not carried out.

CAUTION!

This symbol in connection with the signal word indicates that

material damage or data loss

will occur

if the respective precautionary measures are not taken.

CAUTION!

This symbol indicates that

components could be destroyed

by electrostatic discharge (ESD = Electro

Static Discharge) if the respective cautionary measures are not taken.
Only use the ESD packages intended for this purpose to return device inserts, assembly groups, or as-
sembly components.

1.1.2

Note symbols

NOTE!

This symbol refers to

important information

about the product, its handling, or additional benefits.

1.2

Intended use

The device described in these instructions is used to measure analytical process variables in liquids in
an industrial environment as specified in the technical data. Other uses beyond those defined are not
viewed as intended uses.

READ THE DOCUMENTATION!

This symbol, which is attached to the device, indicates that the associated

documentation for the de-

vice

must be

observed

. This is necessary to identify the nature of the potential hazard, and to take

measures to prevent it.

REFERENCE!

This symbol refers to

additional information

in other sections, chapters, or other manuals.

FURTHER INFORMATION!

This symbol is used in tables and indicates that

further information

is provided after the table.

&

DISPOSAL!

At the end of its service life, the device and any batteries present do not belong in the trash! Please en-
sure that they are

disposed of

properly and in an

environmentally friendly

manner.

«
...
5
6
7
8
9
...
»

Содержание digiLine CR HT10





















































































Отзывы:

Нет отзывов