JUKI MO-6800S Series Скачать руководство пользователя страница 40

Страница: 40 / 72

– 28 –

(16) Adjusting the looper cover

WARNING :

Turn OFF the power before starting the work so as to prevent accidents caused by abrupt start of the

sewing machine.

Standard adjustment

The looper cover

❷

should smoothly close without coming in contact with upper knife

❶

when slowly

closing looper cover

❷

with upper knife

❶

in its lowest position of its stroke.

(17) Adjusting the cloth chip cover

WARNING :

Turn OFF the power before starting the work so as to prevent accidents caused by abrupt start of the

sewing machine.

Standard adjustment

When cloth chip cover

❸

is pressed away from you, it should not rattle.

In addition, the cloth chip cover

❸

should not come in contact with upper knife

❶

and lower looper

❹

❺

❹

❸

❷

❶

❷

Frame

Cloth chip cover

❼
❻

❺

(There are two setscrews on the inside.)

Содержание MO-6800S Series









































































Результаты поиска

Содержание MO-6800S Series

Отзывы:

Похожие инструкции для MO-6800S Series

Бренды по названию

Популярные бренды

JUKI MO-6800S Series, Руководство инженера

Результаты поиска

Содержание MO-6800S Series

Отзывы:

Похожие инструкции для MO-6800S Series

Бренды по названию

Популярные бренды