JUKI LU-2810-6 Скачать руководство пользователя

Страница: 10 / 14

– 8 –

9. WIRING THE MACHINE HEAD

WARNING :

Junction cord preparation and wiring to the control box must be carried out by an electrical engineer

without exceptions. Be sure to turn off the power to the sewing machine and wait for five minutes before

starting the wiring work.

If the pin numbers of the connectors are not correctly connected, errors and breakage of parts and

control box can result. Carefully connect the machine-head connectors and the control-box connectors.

❶

❷

(5) Exhaust tube

Pass

ø8 exhaust air tube

❶

through hole

❷

the table stand and other relevant hole. Then,
route the air tube downward. If the humidity is
high, water may come out of the air tube.

(1) Wiring diagram

Details of the connectors wired to the machine head are as described below.

Refer to

"(2) Details of connectors"

on the next page for details of connectors

①

④

and layout of

the pins.

Tension release solenoid (upper side)

Tension release solenoid (lower side)

Alternate up/down limit switch

Reverse feed switch

6-gang switch

Thread trimming solenoid (right side)

Thread trimming solenoid (left side)

Presser bar lifting cylinder solenoid valve: CN151

Alternate up/down cylinder solenoid valve: CN153

2-pitch cylinder solenoid valve: CN155

FG (earth cord)

Knee switch

③

: CN144 / 16P connector

6-gang switch

④

: CN102 / 12P connector

Solenoid valve

②

: CN36 / 14P connector

Tension release solenoid (lower side)

Tension release solenoid (upper side)

Thread trimming solenoid (left side)

Thread trimming solenoid (right side)

Reverse feed switch

FG (earth cord)

Knee switch

①

: CN158 / 4P connector

Alternate up/down limit switch

(lower side)

Alternate up/down limit switch

(upper side)

Reverse feed cylinder solenoid valve: CN152

Содержание LU-2810-6















Результаты поиска

Содержание LU-2810-6

Отзывы:

Похожие инструкции для LU-2810-6

Бренды по названию

Популярные бренды

JUKI LU-2810-6, Инструкция по эксплуатации

Результаты поиска

Содержание LU-2810-6

Отзывы:

Похожие инструкции для LU-2810-6

Бренды по названию

Популярные бренды