JUKI LS-2342 Скачать руководство пользователя страница 24

Страница: 24 / 31

– 22 –

5-5. Operation switches

When raising the machine head which has been tilted, do not hold the operation switch to raise it.

❶

❷

❸

❹

❺

❻

❶

Alternating vertical movement amount change-

over switch (LS-2342S-7, 2342H-7)

If this switch is pressed the amount of the alternat-

ing vertical movement of the walking foot and the

presser foot will be maximized. (Lamp above the

switch lights up)

Use this switch when a multilayered portion of the

sewing product is not smoothly fed.

To change over the amount of the alternating

vertical movement of the walking foot and the press-

er foot by means of the knee switch, assemble the

accessory knee switch supplied with the unit and fix

it on the table with wood screw.

For the wiring, refer to

"5-6. Knee switch (LS-

2342S-7, 2342H-7)" p.24

❷

Automatic reverse feed stitching cancellation/addition switch

(LS-2342S-7, 2342H-7)

• If this switch is pressed when the following automatic reverse feed stitching has been specified, the reverse

stitching will not take place (for once immediately after it is pressed). (Example 1)

• If this switch is pressed when no automatic reverse feed stitching has been specified, the reverse feed stitching

will take place (once immediately after it is pressed). (Example 2)

(Example 1) In the case where both automatic reverse feed stitching for start and that for end have

been specified :

(Example 2) In the case where neither automatic reverse feed stitching for start nor that for end have

been specified :

If the

switch is pressed before starting sewing,

the automatic reverse feed stitching for start (be-

tween

and

) will not be carried out.

If the

switch is pressed during sewing, the auto-

matic reverse feed stitching for end (between

and

) will not be carried out.

If the

switch is pressed before starting sewing,

the automatic reverse feed stitching for start (be-

tween

and

) will be carried out.

If the

switch is pressed during sewing, the auto-

matic reverse feed stitching for end (between

and

) will be carried out.

Содержание LS-2342
































Результаты поиска

Содержание LS-2342

Отзывы:

Похожие инструкции для LS-2342

Бренды по названию

Популярные бренды

JUKI LS-2342, Инструкция по эксплуатации

Результаты поиска

Содержание LS-2342

Отзывы:

Похожие инструкции для LS-2342

Бренды по названию

Популярные бренды