JUKI LBH-1790AN Скачать руководство пользователя страница 27

Страница: 27 / 88

– 24 –

1-pedal

(With intermediate

position)

2-pedal

1-pedal

(Without intermediate

position)

1-pedal

(With a depress on the

back part of the pedal)

For this sewing machine, the pedal operation method to be used can be selected from among the four dif-
ferent ones as described on the next page. Select the operating procedure you desire for working efficien-
cy and use the sewing machine.

(1) Setting procedure of the pedal type
1) Call the pedal type setting parameter.

Keep MODE key

❹

held pressed for

three seconds under the input mode where SET
READY LED

goes out. Then, the MEMORY

switch (level 2) is displayed on the menu.
Select the target item with ITEM SELECT key

❻

and press EDIT key

❽

. Then, the

memory switch (level 2) edit screen

is dis-

played.
When the pedal type selection parameter

is not displayed, press ITEM SELECT key

❻

to select the pedal type.

2) Select the pedal type.

Press DATA CHANGE key

❼

and the pic-

ture is changed as shown in the illustration below.

Select the pedal type

you desire.

3. How to use the pedal

❹

❽

❼

❻

Содержание LBH-1790AN

























































































Результаты поиска

Содержание LBH-1790AN

Отзывы:

Похожие инструкции для LBH-1790AN

Бренды по названию

Популярные бренды

JUKI LBH-1790AN, Инструкция по эксплуатации

Результаты поиска

Содержание LBH-1790AN

Отзывы:

Похожие инструкции для LBH-1790AN

Бренды по названию

Популярные бренды