JUKI LBH-1790A Series Скачать руководство пользователя страница 4

Страница: 4 / 79

– 1 –

I. IMPORTANT SAFETY INSTRUCTIONS

II. SPECIFICATIONS

Main specifications of the LBH-1790A computer-controlled, lockstitch buttonholing machine

1. Specifications

1) Never operate the machine unless the oiling tank has been properly lubricated.

2) Be sure to remove any dust from the hook or bobbin thread cutting knife section at the end of the day,

and check the amount of oil remaining.

3) Be sure to return the activating pedal to the home position after the machine has started to run.

4) This machine is provided with a machine head tilt detector so that it cannot be operated in the state

that the machine head is tilted. When operating this sewing machine, turn the power switch ON after

setting the sewing machine to the bed base properly.

Sewing speed

Standard speed : 3,600 sti/min (Max. : 4,200 sti/min) (Max. : 3,300 sti/min when dry hook is used)

Needle

DPX5 #11J to #14J

Hook

DP type full-rotary hook

Needle rocking
drive method

Drive by stepping motor

Feed drive method

Drive by stepping motor

Presser lifting drive
method

Drive by stepping motor

Lift of presser foot

14 mm (Optional setting available) Max. : 17 mm (At the time of needle up by reverse run)

Cloth cutting knife
drive method

Motor-driven crank system

Standard sewing
shape

31 kinds

Number of patterns
stored in memory

99 patterns

Motor used

3-phase 200 to 240 V, 370 VA

Noise

- Equivalent continuous emission sound pressure level (L

) at the workstation :

A-weighted value of 81.0 dB ; (Includes ; K

= 2.5 dB) ; according to ISO 10821- C.6.3 -ISO

11204 GR2 at 3,600 sti/min.

Subclass

Major application

Buttonholing of cloth such as men’s shirts, blouses,

work uniforms, ladies' wear, etc.

Buttonholing size

Knife size used :

6.4 to 31.8 mm (1/4' to 1-1/4')

Buttonholing sewing length

Standard : Max. 41 mm

Special type part : Max. 120 mm

Standard : Max. 5 mm

Special type part : Max. 10 mm

Содержание LBH-1790A Series
















































































Результаты поиска

Содержание LBH-1790A Series

Отзывы:

Похожие инструкции для LBH-1790A Series

Бренды по названию

Популярные бренды

JUKI LBH-1790A Series, Инструкция по эксплуатации

Результаты поиска

Содержание LBH-1790A Series

Отзывы:

Похожие инструкции для LBH-1790A Series

Бренды по названию

Популярные бренды