JUKI J-350QVP Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 32

JUKI J-350QVP Скачать руководство пользователя страница 19

– 18 –

Adjusting the thread tension

As a measure of the thread tension applied by the bobbin case, when
a bobbin (Cotton TEX40) is loaded in the bobbin case, the bobbin

should slowly drop by its own weight as illustrated in the figure.

* Adjust the needle thread tension in accordance with the bobbin

thread tension.

* The bobbin case for the J-350QVP is an exclusive JUKI part. Please

consult the JUKI dealers when you purchase it.

·

Proper thread tension

Improperly adjusted thread tension may cause
puckering on materials, inferior stitches, or
thread breakage.

Center of the

material

Needle thread

Bobbin thread

Bobbin thread

Needle thread

Bobbin thread

The needle thread tension is too low

The needle thread tension is too high

Thread tension dial

Increase the needle

thread tension.

Decrease the needle

thread tension.

· Adjusting the bobbin case

Needle thread

Tension adjusting

screw

Increase

Decrease

CAUTION

Turn OFF the power switch before taking out the bobbin case or replacing the needle.

«
...
17
18
19
20
21
...
»

Содержание J-350QVP

































Отзывы:

Нет отзывов