JUKI APW-896N/IP-420 Скачать руководство пользователя страница 51

Страница: 51 / 142

− 47 −

(4) Erasing the pattern

①

Display the input screen

When the input screen of independent sewing mode, alternate sewing mode and cycle sewing mode is
displayed, it is possible to erase the pattern.

②

Call the pattern list screen

Press PATTERN LIST button

and the pattern No. list screen (screen A) is dis-

played.

③

Select the pattern to be erased

Select the pattern to be erased from pattern list button

Next, press ERASE button

and the pattern erase confirmation screen is displayed.

Pattern No. list screen (screen A)

④

Determine the pattern to be erased

Press ENTER button

in the pattern erase confirmation screen and the pattern is erased.

When CANCEL button

is pressed, the screen returns to the original screen A without erasing the

pattern.

Содержание APW-896N/IP-420















































































































































Результаты поиска

Содержание APW-896N/IP-420

Отзывы:

JUKI APW-896N/IP-420, Инструкция по эксплуатации, Страница: 51 / 142

Результаты поиска

Содержание APW-896N/IP-420

Отзывы: