JUKI AMS-221F3020RSW/AW-3 Скачать руководство пользователя страница 24

Страница: 24 / 163

– 19 –

1) Open hook cover

❶

2) Raise latch

❸

of bobbin case

❷

, and re-

move the bobbin case.

3) When entering bobbin case, insert it with the

latch tilted until “click” sounds.

4-4. How to thread the device with the bobbin thread (RSZ type)

If it is not fully inserted, bobbin case

❷

may slip off during sewing.

WARNING :

Turn OFF the power before starting the work so as to prevent accidents caused by abrupt start of

the sewing machine.

1) Set the bobbin

❶

into bobbin case

❷

in the

direction shown in the figure.

2) Pass the thread through thread slit

❸

of bob-

bin case

❷

, and pull the thread as it is. By so

doing, the thread will pass under the tension
spring and be pulled out from thread hole

❹

3) Draw out the thread from thread opening

❹

by 4 cm.

If the bobbin is installed in the bob

bin case orienting the reverse direc

tion, the bobbin thread pulling out
will result in an inconsistent state.

❶

❷

❸

4 cm

❸

❷

❶

❹

4-4-1. Installing and removing the bobbin case

4-4-2. Installing the bobbin

Содержание AMS-221F3020RSW/AW-3




































































































































































Результаты поиска

Содержание AMS-221F3020RSW/AW-3

Отзывы:

JUKI AMS-221F3020RSW/AW-3, Инструкция по эксплуатации, Страница: 24 / 163

Результаты поиска

Содержание AMS-221F3020RSW/AW-3

Отзывы: