JUKI AMS-221F3020RSW/AW-3 страница 102 Скачать руководство пользователя

Страница: 102 / 163

– 97 –

2-8-1. Maintenance personnel management setting

This is the function to display the warning screen when the counter reaches its target value.

As many as five warning items can be set.

1) Setting the warning counter

The warning level setting can be carried out on the screen shown
in the case of the maintenance personnel level.

①

Displaying the warning counter setting screen

When is held pressed for three seconds on the pattern

setting screen, the information list screen (maintenance per-
sonnel level) is displayed.

②

Displaying the warning counter setting screen

When

is pressed on the information

list screen, the warning counter setting screen is displayed.

③

Setting enable / disable of the warning counter

It is possible to select enable / disable of the warning counter
with

. Every time

is pressed, enable / disable

status of the warning counter is changed over.

・

When the warning counter is enabled, the counter carries out

counting.

・

When the warning counter is disabled, the counter does not

carry out counting.

④

Setting display / hide of the clear button when the

warning screen is displayed

It is possible to select display / hide of the clear button with

when the warning screen is displayed.

Every time

is pressed, display / hide status of the

clear button is changed over.

Содержание AMS-221F3020RSW/AW-3




































































































































































Результаты поиска

Содержание AMS-221F3020RSW/AW-3

Отзывы:

Похожие инструкции для AMS-221F3020RSW/AW-3

Бренды по названию

Популярные бренды

JUKI AMS-221F3020RSW/AW-3, Инструкция по эксплуатации

Результаты поиска

Содержание AMS-221F3020RSW/AW-3

Отзывы:

Похожие инструкции для AMS-221F3020RSW/AW-3

Бренды по названию

Популярные бренды