SKY UNIVERSAL 4 BUTTON REMOTE JH-TX278
Auto-scan type multi-frequency duplicator remote
The SKY model JH-TX278 is a 4 button duplicating remote control that can copy the signal from up to 4 fixed code and or
rolling code remote controls. Each button of the remote is independently programmable so it can learn from different brands
and types of remote controls. This feature makes the model JH-TX278 extremely flexible since it can duplicate the signal of all
of the remotes on the market today that operate between 280MHz to 870MHz frequency. In order to preserve the battery and
as well assist with preventing the opener from opening and closing by itself in the event the button is accidentally held down
while in a purse or pocket, the remote control has a 6 second time out feature that will turn the remote off. Once the remote
button is released the remote will then operate normally again.
Programming:
1. Hold the original remote you wish to copy from close to the duplicator remote 2 to 3 cm (1/2” to 1”).
2. Press and hold down button 1 (the LED comes on) then press and release button 2 four times (the LED goes out then flashes
every 2 seconds indicating it is in learn mode).
3. While the LED is blinking slowly and within 15 seconds press and hold the button of the remote you wish to copy from.
4. When the LED on the remote flashes rapidly press and hold the button that you wish to use on the duplicator remote until
the LED comes on solid then goes out indicating that the button has learned the code.
5. Repeat the above step to program the additional buttons as needed.
NOTE: When duplicating rolling code type remotes (such as S, Intellicode) once the duplicator remote has learned
from the original remote it will then need to be learned by the radio receiver of the gate or garage door opener before it will
work. Follow the manufactures instructions on how to program a remote to it.
Typically for most openers that use a learn button, press and release the learn button so the LED comes on. Then press the
remotes button a few times until the opener activates.
Battery Replacement: To replace the battery separate the top by placing a small screwdriver in the slot at the bottom of the
remote. Then tilt the screwdriver away from the color ring to separate. When a gap appears move around the remote to pull the
two parts apart. Once the case has been separated use the small screwdriver and insert it at the top center of the battery and
slide it down as far as possible then repeat at one side to slide it out the rest of the way. The new battery can then be inserted
making sure the + side is up. Place top of the case back on and press so it snaps back into place. Only replace using a CR2032
3V coin cell battery.
Key Ring Attachment: To install the key ring attachment accessory separate the top of the case as described above then insert
the wire string though the hole and loop the metal portion through the middle of the loop and pull.
Warranty: This remote carries a one-year manufactures warranty against defects in workmanship or materials commencing
from the purchase date of the remote. For warranty claims the remote need to be returned to the dealer or distributor it was
purchased from. Remotes4Less does not assume, and is not responsible for any real or consequential damages from claims
against performance of this remote, nor is it liable for any costs related to loss of life, property, or revenue and will assume no
costs of reinstallation or removal.
© 2017 Remotes4Less All rights reserved.
Distributed by: Remotes4Less, Apple Valley CA www.remotes4less.com
Manufactured by: Quanzhou Juhui Electronic Co. Ltd.
WARNING
To prevent possible SERIOUS INJURY or DEATH:
•
NEVER allow small children near batteries.
•
If battery is swallowed, immediately notify doctor.
•
To reduce the risk of fire, explosion or chemical burn replace only with a CR2032 3V coin cell battery.
•
DO NOT recharge, disassemble, heat above 212
°
(100
°
C) or incinerate.
NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of this transmitter are prohibited, except for changing the
signal learned or replacing the battery. THERE ARE NO OTHER SERVICABLE PARTS.
Tested to comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following two conditions: (1) this device may not cause
any harmful interference, and (2) this device must accept any interference received, including interference that may cause undesirable operation.
