JRC JHS-770S - Скачать руководство пользователя | Manualshive

Страница: 156 / 162

background image

Options Operation

10-4

10.4

VHF Channel selector (NCM-2000)

CAUTION

For channel selectors installed above deck, close the water-resistant cap after use. Rain
and sea breeze could cause connector malfunction. Also do not leave the handset
above deck.

1.

TX Lamp

Lights when transmitting.

2.

1W Lamp

Lights when transmitting power is 1W.

3.

OCC Lamp

Lights when not having the access right.

4.

25W/1W Switch

Switches transmitting power between 25W and 1W. If pressed and held for two seconds, this unit becomes
to the menu mode. In this mode, select the desired item with the

▲

or

▼

key and press ENT, then perform

the procedure in the table below. When finishing this menu mode, press and hold for two seconds again.

Display Setting

Setting

Method

S.1

Squelch level

Select 01

(open)

- 32 with the

▲

or

▼

key, and press ENT.

S.2

PHONE level

Select 01 - 08 with the

▲

or

▼

key, and press ENT.

S.3

Hook switch detection function

Select ON/OFF with the

▲

or

▼

key, and press ENT.

S.4 Fine

brightness

1) Select a brightness level from bright (d.1), medium

(d.2), or dark (d.3) with the

▲

or

▼

key, and press

ENT.

2) Select the fine brightness value (01-10) for the

brightness level selected in 1) with the

▲

or

▼

key,

and press ENT.

S.5

Software version

Display a software version.

S.0

(Ends the menu mode.)

-----

1

2

3

4

5

6

8

7

9

10

«
...
154
155
156
157
158
...
»

Содержание JHS-770S -



































































































































































Отзывы:

Нет отзывов

Похожие инструкции для JHS-770S -

Бренд: Fein Страницы: 248

Бренд: ZF Страницы: 30

Бренд: Raymarine Страницы: 111

Бренд: ZIGBEE Страницы: 6

Бренд: Daisy Страницы: 2

Below Ground Pool Cover Box

Бренд: Daisy Страницы: 3

Бренд: Eazyzap Страницы: 32

Бренд: Obdstar Страницы: 42

Бренд: Haag-Streit Страницы: 16

Бренд: M-system Страницы: 5

Бренд: MA Страницы: 2

ENET-232 Series

Бренд: National Instruments Страницы: 105

Бренд: Accurate Technology Страницы: 10

Бренд: Gage Bilt Страницы: 28

Бренд: mychway Страницы: 56

Бренд: Wang Страницы: 146

Бренд: Qtx Страницы: 6

Бренд: Hussmann Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды