JOSAM SUPER FLO GI-2000 Series Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 41

JOSAM SUPER FLO GI-2000 Series Скачать руководство пользователя страница 33

8.4.5 SET

CALIBRATION

OFFSET

This function allows the user to adjust offsets in the calibration level when the tank is full
of water. Normally the test water level reading with the tank full of water is 4.0 inches. If
the test water level is not 4.0 inches use this function to adjust the test water level
reading to 4.0 inches. The maximum offset is +/- 2.5 inches of water. Normally after a full
calibration this calibration offset will be set to 0.0 inches.

CAL MODE–USE UP/DWN
KEYS TO SET CAL
OFFSET, ENTER TO
FINISH. +X.X INCHES

Pressing the Enter button will display:

CAL MODE–CAL OFFSET
INCHES ENTERED
SET TO: +X.X INCHES

The unit returns after a few seconds to automatic or manual display modes.

8.4.6 CLEAN CYCLE LIMIT

This function allows the user to override the automatic clean cycle limit of no more than
one clean cycle every 12 hours. After each clean cycle the clean cycle limit is enabled.

Note:

Disabling this function is typically only used for test purposes.

CAL MODE–USE UP/DWN
KEYS TO ENABLE OR
DISBALE CLEAN CYCLE
12HR LIMIT–DISBALED

Pressing the Enter button will display:

CAL MODE–CLEAN CYCLE
12 HR LIMIT SET TO
-DISABLED

GI-2000 Manual V2.3

Page

33

The unit returns after a few seconds to automatic or manual display modes

«
...
31
32
33
34
35
...
»

Содержание SUPER FLO GI-2000 Series










































Отзывы:

Нет отзывов