background image

 

 

 

 

 
INSTALLATION INSTRUCTIONS 

   5b. Top inlet connection. 

 

Connect the outlet to an oil/water separator.  

                        

 

-We advise to use the outlet nipple delivered with the 
KAPTIV-CS-HP-S. If it is necessary to use an 
alternative nipple, make sure it has the correct 
thread (1/4”BSP), do not over tighten!

 

  7. Power cable connection 

Remove the protection cab from the connector 
and connect your power cable as shown.

 

 
 
 
 
 
 
5. Power cable connection 

Remove the protection cap from the connector 
and connect your power cable as shown. 

 
 

 
 
 
 
 
 

 

 

     

    

 
                        

 
 
 
 
 
 
 
 
 
 
 
 
 

 
 
 
 
 
 
 
         
                 
             
 
 
               

               

 

          

 
 
 
 
 
 
 
          
         

 
 
 
 
 

 
    

  

 

9. Press and hold down the TEST button to 
check the valve function.

 

         

 

10. Your KAPTIV-CS-HP-S is ready for  
operation! 

 

 

 

 

 

 

Power 

Connection 

 

 

      

 

-We advise to use the outlet nipple delivered with 
the KAPTIV-CS-HP-S. If it is necessary to use an 
alternative nipple, make sure it has the correct 
thread (1/4”BSP), do not over tighten!

 

 

8. Slowly open the ball valve to restore  
normal system pressure.

    

6b. Side inlet connection.

  

Connect the outlet to an oil/water separator.

 

Содержание KAPTIV-CS-HP-S











Отзывы: