Jonsered 1188S CE Скачать руководство пользователя

Страница: 61 / 96

10. During operation

10.1. Operate the crane

Lifting should be carried out in the following order:

1. Lift the load.
2. Move load closer to the crane.
3. Slew
4. Lower the load.

WARNING

• Never go underneath a hanging load or move a load over people.

• The crane may not be used for lifting personnel

Comply with the values listed on the load plate; do not overload the crane. Follow the operation of
the load warning indicator. The warning lights will flash when the load exceeds 90 % of the
maximum allowed value.

If possible, lift the load from its center of gravity. Do not lift a log from its top end.

Do not lift a load over yourself or the cab

• Never drive the cylinders to their extreme positions at full

speed.

• Never operate the stabiliser system while the crane is

loaded.

• Ensure that the weight of the load and the vehicle does

not rest solely on the stabiliser system. Adjust the
stabiliser leg if necessary.

• Do not load from in front of the vehicle: there is a risk of the vehicle tilting over!

During operation

Jonsered 1188S CE

Содержание 1188S CE

































































































Результаты поиска

Содержание 1188S CE

Отзывы:

Похожие инструкции для 1188S CE

Бренды по названию

Популярные бренды

Jonsered 1188S CE, Руководство оператора

Результаты поиска

Содержание 1188S CE

Отзывы:

Похожие инструкции для 1188S CE

Бренды по названию

Популярные бренды