Jolimark TP830 Series Скачать руководство пользователя страница 10

Страница: 10 / 65

TP830 User's Manual

- 5 -

2.3.4 Connecting the Serial Interface Cable

1. Make sure the computer and the printer are both turned off, plug the serial cable to the serial

interface of the printer. Tighten the screws on both sides and make the cable fixed. As shown in
Figure 2-5.

2. Plug the other end of the cable to the computer’s serial interface. Tighten the screws on both sides

and make the cable fixed

2.3.5 Connecting the Ethernet Interface Cable

1. Plug the crystal end of the Ethernet cable (RJ-45) into the printer's Ethernet interface and the other

end to the LAN. (As shown in Figure 2-6)

Figure 2-5 Connecting the serial interface cable

Figure 2-4 Connecting the USB interface cable

Figure 2-6 Connecting the Ethernet interface cable

USB interface

USB interface cable

Screws

Serial interface cable

Serial interface

Ethernet interface

Ethernet interface cable

Содержание TP830 Series


































































Результаты поиска

Содержание TP830 Series

Отзывы:

Jolimark TP830 Series, Руководство пользователя, Страница: 10 / 65

Результаты поиска

Содержание TP830 Series

Отзывы: