Johnson Controls YORK OPTIVIEW CONTROL CENTER Скачать руководство пользователя страница 84

Страница: 84 / 142

JOHNSON CONTROLS

FORM 160.10-O1

ISSUE DATE: 4/27/2018

SECTION 2 - OPTIVIEW OPERATION

ACC to VSD

This displays the number of communication error

counts from the ACC board to the VSD.

VSD to ACC

This displays the number of communication error

counts from the VSD to the ACC board.

PROGRAMMABLE
Reset Counters

This key allows the service technician to reset the

VSD, ACC, and panel error counters.

NAVIGATION
Home

Access Level Required: VIEW

Returns the display to the Home screen.

Diagnostics

Access Level Required: VIEW

Returns the display to the Diagnostics screen.

OVERVIEW

This screen displays communication error counts for

the OptiView panel, ACC, and VSD. This screen is

useful for service technicians checking communication

error counts between these components.

Requires a login access level of SERVICE

to view. Service technicians refer to Op-

tiView Control Center Retrofit Kit - Trane

Service Manual (Form 160.10-M1) for

further explanation of displayed values.

DISPLAY ONLY
Panel to ACC

This displays the number of communication error

counts from the adaptive capacity control (ACC) board

to the OptiView panel.

ACC to Panel

This displays the number of communication error

counts from the OptiView panel to the ACC board.

DIAGNOSTICS - VSD SCREEN

ID10024

FIGURE 34 -

VSD DIAGNOSTIC SCREEN

Содержание YORK OPTIVIEW CONTROL CENTER















































































































































Результаты поиска

Содержание YORK OPTIVIEW CONTROL CENTER

Отзывы:

Похожие инструкции для YORK OPTIVIEW CONTROL CENTER

Бренды по названию

Популярные бренды

Johnson Controls YORK OPTIVIEW CONTROL CENTER, Руководство по эксплуатации

Результаты поиска

Содержание YORK OPTIVIEW CONTROL CENTER

Отзывы:

Похожие инструкции для YORK OPTIVIEW CONTROL CENTER

Бренды по названию

Популярные бренды