Johnson Controls YORK OPTIVIEW CONTROL CENTER Скачать руководство пользователя страница 80

Страница: 80 / 142

JOHNSON CONTROLS

FORM 160.10-O1

ISSUE DATE: 4/27/2018

SECTION 2 - OPTIVIEW OPERATION

GPIC

Displays the EPROM installed in the MicroGateway,

as equipped.

PROGRAMMABLE

None

NAVIGATION
Home

Access Level Required: VIEW

Returns the display to the Home screen.

Setup

Access Level Required: VIEW

Returns the display to the Setup screen.

Analog I/O

Access Level Required: SERVICE

Advances to a sub-screen which details voltage levels

and counts for internal and external analog inputs.

OVERVIEW

The Diagnostics screen identifies software version in-

formation. This screen also serves as a gateway to view

analog and digital input/output screens.

Requires a login access level of SERVICE

to view. Service technicians refer to Op-

tiView Control Center Retrofit Kit - Trane

Service Manual (Form 160.10-M1) for

further explanation of displayed values.

DISPLAY ONLY
Controls

Displays version of flash software installed/loaded into

the microboard.

BIOS (Basic Input/Output Software)

Displays the version of the BIOS EPROM installed in

the microboard.

Kernal

Displays the operating system core components in-

stalled/loaded into the microboard.

DIAGNOSTICS SCREEN

LD26951

FIGURE 31 -

DIAGNOSTICS SCREEN

Содержание YORK OPTIVIEW CONTROL CENTER















































































































































Результаты поиска

Содержание YORK OPTIVIEW CONTROL CENTER

Отзывы:

Похожие инструкции для YORK OPTIVIEW CONTROL CENTER

Бренды по названию

Популярные бренды

Johnson Controls YORK OPTIVIEW CONTROL CENTER, Руководство по эксплуатации

Результаты поиска

Содержание YORK OPTIVIEW CONTROL CENTER

Отзывы:

Похожие инструкции для YORK OPTIVIEW CONTROL CENTER

Бренды по названию

Популярные бренды