background image

TEC22x1-3 L

ON

W

ORKS

® Networked Single Stage Thermostats Installation Instructions 

15

Thermostat does 
not call for heating

Wrong mode 
selected

Select heating mode.

Thermostat in 
Unoccupied mode

Select Override to force the thermostat Occupied heating setpoint.

Anticycle delay 
active

Wait, the anticycling period must end before the equipment can start.

Heating setpoint is 
satisfied

Raise the Heating setpoint.

Heating lockout 
attained 

Mode is locked out based on outside air temperature.
Change configuration parameter H Lock to value 120°F (49°C) to by-pass 
lockout.

Wiring error 

Start the Fan by forcing the Fan ON mode.
Put a jumper across terminals RH and W1. The heating should come ON. 
If it does not, verify wiring .and check if a jumper is required between RC 
and  RH

Thermostat does 
not call for cooling

Wrong mode 
selected

Select cooling mode.

Thermostat in 
Unoccupied mode

Select Override to force the thermostat Occupied cooling setpoint.

Anticycle delay 
active

Wait, the anticycling period must end before the equipment can start.

Cooling setpoint is 
satisfied

Lower the cooling setpoint.

Cooling lockout 
attained

Mode is locked out based on outside air temperature.
Change configuration parameter C Lock to value -40°F (-40°C) to by-pass 
lockout.

Wiring error

Start the Fan by forcing the Fan ON mode.
Put a jumper across terminals RC and Y1. The cooling should come ON. 
If it does not, verify wiring.

The thermostat 
does not turn on 
the fan 

Wiring error

Start the Fan by forcing the Fan ON mode
Put a jumper across terminals RC and G. The fan should come ON If it 
does not, verify wiring.

Digital display 
shows missing 
digits or erratic 
segments

Defective display

Replace thermostat.

Table 9:  Display Messages

Display

Function

Service

Indicates that there is a service alarm in accordance with the programmable Digital Inputs (DI1 or DI2)

Filter

Indicates that the filter(s) is dirty in accordance with the programmable Digital Inputs (DI1 or DI2)

Frost ON

Indicates that the heating is energized by the low limit frost protection room temperature setpoint.

SetClock

Indicates that there has been a power failure greater than 6 hours and the clock needs to be reset.

Table 8:  Troubleshooting Details (Part 2 of 2)

Symptom

Cause

Solution(s)

Содержание TEC22x1-3 LONWORKS


















Отзывы: