background image

TEC22x2-3 L

ON

W

ORKS

® Networked Heat Pump Thermostat Installation Instructions

4

Connecting the L

ON

W

ORKS

 Network

The wiring rules for the L

ON

W

ORKS

 network differ from 

the wiring rules for the Metasys® N2 Bus and the 
BACnet® MS/TP Bus. For more details on wiring the 
L

ON

W

ORKS

 network, refer to the 

L

ON

W

ORKS

 Network 

Layout Technical Bulletin (LIT-1162150)

.

To connect the thermostat to the L

ON

W

ORKS

 network:

1.

Connect the L

ON

W

ORKS

 network wires to the

L

ON

W

ORKS

 network terminal block on the

thermostat (Figure 5, Figure 6, Figure 7, and
Figure 8).

Note:

There is no polarity when connecting the 

L

ON

W

ORKS

 network wires to the thermostat; however, 

we recommend keeping the polarity consistent 
throughout the network. 

2.

After the L

ON

W

ORKS

 network wires are connected

to the first thermostat, continue in a daisy-chained
fashion to the next device.

Note:

The L

ON

W

ORKS

 network wiring must be twisted-

pair lines.

Do not run the L

ON

W

ORKS

 network wiring in the same 

conduit as line voltage wiring (30 VAC or above) or 
other wiring that switches power to highly inductive 
loads (such as contactors, coils, motors, or 
generators).

The L

ON

W

ORKS

 network requires proper termination 

and biasing at the end of a segment (a segment is a 
physically continuous length of wire). The thermostat is 
not equipped with the ability to provide this termination; 
therefore, it cannot be located at the physical end of a 
L

ON

W

ORKS

 network segment unless a terminator is 

attached. Refer to 

L

ON

W

ORKS

 Network Layout 

Technical Bulletin (LIT-1162150)

 for end-of-line 

solutions.

Figure 7: VDC Switching Application for Heat Pumps

Separate 24 VAC

Transformer

Y2

Y1

G

RC

C

RH

W1

O/B

R4

To Auxiliary

Heat Circuit

Heat Pump Terminal Interface

R4-1

R1-1

R2-1

R3-1

R3

R1

R2

Note: 

Use 24 VAC

interface relays R1-1,
R2-1, R3-1, and R4-1
(provided by the user).

Y2

Y1

G

RC

O/B

F

IG

:h

t_

p

m

p

Figure 8: Thermostat to Network Connection

Supervisory 

Controller

Twist wires together 
before inserting them into 
the terminals.

F

IG

:L

O

N

_

w

ir

L

W

ON

ORKS

 

Network Wires

L

W

ON

ORKS

Network 

Terminal Block

L

W

 

Bus Terminals

ON

ORKS

Содержание TEC22 2-3 LonWorks Series




















Отзывы: