background image

22    

T500 Series Programmable Thermostats Product/Technical Bulletin

O

rdering information

Table 9: Ordering Information

Item

Product Code Number

Programmable Thermostat, Single-stage, 1 Heat, 1 Cool

T500HCP-1

Programmable Thermostat, Multi-stage, 2 Heat, 2 Cool

T500MSP-1

Programmable Thermostat, Heat Pump, 3 Heat, 2 Cool

T500HPP-1

Programmable Thermostat, Heat Pump, 1 Heat, 1 Cool

T500HPP-2

A

ccessories

Table 10: Optional Accessories (includes mounting hardware)

Item

Product Code Number

Remote Indoor Temperature Sensor

SEN-500-1

Outdoor Air Temperature Communication Module with Outdoor Air Sensor

SEN-500-2

Outdoor Air Temperature Communication Module with Duct Mount Sensor

SEN-500-3

Conversion Module

ACC-500-1

Thermostat Wall Plate

ACC-500-2

R

eplacement and Repair Parts

The SEN-500 series of products allows for easy
replacement of the sensor. For a replacement sensor,
contact the nearest Johnson Controls branch office or

wholesale distributor and order using the information
from 

Table 10:

 

Optional Accessories,

 

Table 11:

Replacement

 

Parts, 

and 

Table 12:

 

Repair Parts

.

Table 11: Replacement Parts

Item

Product Code Number

Replacement Outdoor Air Temperature Communication Module

SEN-500-603

Replacement Outdoor Air Temperature Sensor (including mounting hardware)

SEN-500-604

Replacement Duct Mount Temperature Sensor (including mounting hardware)

SEN-500-605

Table 12: Repair Parts

Item

Product Code Number

3 in. Sensor Probe (use with outdoor air sensor)

SEN-500-601

8 in. Sensor Probe (use with duct mount sensor)

SEN-500-602

Содержание T500HCP-1

























Отзывы: