Johnson Controls SABROE SAB 120 E страница 38 Скачать руководство пользователя | Manualshive

Страница: 38 / 62

background image

Operating manual - SAB 120-151 A-frame (including ATEX)

38/61

008668 en 2019.08

Operating instructions

6.12

Automatic oil return valve

Fig. 17

Note:

Valve inlet and outlet are marked on the valve housing with "in" and “out”.

Function

The function of the automatic oil return valve, EVRB, is to return the separated oil in the fine sepa-
rator to the compressor.

Oil and gas from the fine separator flow into the oil return valve at pos. 1, through the filter, pos.
2, and via the nozzles, pos. 7 and 8, and back to the compressor through the outlet, pos. 5, see
Fig. 18.

The gas and oil flow through the nozzles, pos. 7 and 8, is adapted to the spring force of pos. 9 as
well as the viscosity difference between the oil and the gas. Consequently, the pressure loss of
the gas flow through the nozzle, pos. 7, is unable to move the piston, pos. 7.

However, the pressure loss of the oil flow through the nozzle, pos. 7, is able to move the piston,
pos. 7.

Thus the spring force, pos. 9, is equalised and a transverse bore, pos. 10, with a considerably
larger bore than pos. 7, will open.

Because the bore is larger, oil collections at the oil return valve inlet can quickly be removed.

When the oil has been removed, the gas flow will rise, and the piston, pos. 7, will close the trans-
verse bore. The gas flow will be lowered to a minimum.

Through the sight glass, pos. 6, it is possible to watch the oil return. As a small amount of gas will
always pass through the nozzle, pos. 7, gas bubbles will be visible.

The valve can be serviced by closing the stop valves, pos. 3 and 4.

5

1

5

1

3

4

6

2

5

1: Inlet G1/4”
2: Filter
3: Stop valve, inlet side

4: Stop valve, outlet side
5: Outlet G1/4”
6: Sight glass

«
...
36
37
38
39
40
...
»

Содержание SABROE SAB 120 E































































Отзывы:

Нет отзывов

Похожие инструкции для SABROE SAB 120 E

Бренд: Gardner Denver Страницы: 18

Бренд: NARDI COMPRESSORI Страницы: 56

Бренд: California Air Tools Страницы: 17

Бренд: Fubag Страницы: 19

Бренд: Ariel Страницы: 141

VDC 400/100 CM3

Бренд: Fubag Страницы: 15

Бренд: Hanbell Страницы: 51

Бренд: California Air Tools Страницы: 16

Бренд: Aerotec Страницы: 90

Бренд: Kobalt Страницы: 84

Бренд: Mea Страницы: 41

Бренд: Mea Страницы: 81

Бренд: KMR Страницы: 56

Бренд: Mannesmann Страницы: 33

Blackmer TYPHON 1000

Бренд: Dover Страницы: 21

Бренд: sullar Страницы: 52

Dynamite Power Air Compressor

Бренд: Wagan Страницы: 7

Бренд: Parkside Страницы: 148

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды