manualshive.com logo in svg

Johnson Controls PCV1617, Руководство по установке, Страница: 25 / 28

Поделиться
Скачать
Johnson Controls PCV1617 Скачать руководство пользователя страница 25

Table 9: PCV1617 and PCV1632 Controller accessories (order separately)

Product code number

Description

AP-TBK1002-0

2-position Screw Terminal that plugs onto PCV Output Point

Spade Lugs

AP-TBK1003-0

3-position Screw Terminal that plugs onto PCV Output Point

Spade Lugs

AP-TBK4SA-0

Replacement MS/TP SA Bus Terminal, 4-Position Connector,

Brown, Bulk Pack of 10

AP-TBK4FC-0

Replacement MS/TP FC Bus Terminal, 4-Position Connector, Blue,

Bulk Pack of 10

AP-TBK2PW-0

Replacement Power Terminal, 2-Position Connector, Gray, Bulk

Pack

F-1000-325

Replacement Barbed Fitting for use with the PCV1617 and CH-

PCV1632 for Connection Tubing (Bulk Pack of 10)

F-1000-326

Flexible Tubing Extension for use with the PCV1617 and

PCV1632, 14 in. (36 cm) Length (Bulk Pack of 20)

NS-WALLPLATE-0

Network Sensor Wall Plate

TE730-29C-0

Sensor with Temperature Setpoint Adjustment

TE730-39C-0

Sensor with Temperature Setpoint Adjustment and Occupancy

Button

CN-BRTR-0

BACnet IP to MS/TP Router

PCX Series Expansion Input/

Output Modules

Refer to the 

PC Series Programmable Controllers and Related

Products Product Bulletin (LIT-12011914)

 for a complete list of

available PCX Expansion I/O Modules.

NS Series Sensors

Refer to the 

NS Series Network Sensors Product Bulletin

(LIT-12011574) 

for a complete list of available NS Series Sensors.

Technical specifications

Table 10: PCV1617 and PCV1632 Controllers

Product Code

CH-PCV1617-1: 

32-bit, Integrated VAV Controller/Actuator/

Pressure Sensor - DPT, 3 UI and 2 BO, 24 VAC, FC and SA Bus,

includes 8-pin TSTAT Port for use with TE-7xx Series Non-

Communicating Sensors

CH-PCV1632-1: 

 32-bit, Integrated VAV Box Controller/Actuator/

Pressure Sensor; 3 UI, 3 BO, and 2 CO; 24 VAC; FC and SA Bus;

includes 8-pin TSTAT Port for use with TE-7xx Series Non-

Communicating Sensor

Supply Voltage

24 VAC (nominal, 20 VAC minimum/30 VAC maximum), 50/60 Hz,

Power Supply Class 2 (North America), Safety Extra-Low Voltage

(SELV) (Europe)

25

PCV1617 and PCV1632 VAV Box Controllers Installation instructions

Содержание PCV1617





























Отзывы:

Нет отзывов