Johnson Controls PCA3613 Скачать руководство пользователя страница 21

Страница: 21 / 30

Table 5: Communications bus and supply power terminal blocks, functions, ratings,

requirements, and cables

Terminal

block/Port

label

Terminal labels

Function, electrical ratings/

Requirements

Recommended cable

type

+
-

FC Bus Communications

COM

Signal Reference (Common) for Bus

communications

FC BUS

SHLD

Isolated terminal (optional shield

drain connection )

0.6 mm (22 AWG)

stranded, 3-wire

twisted, shielded cable

recommended

+
-

SA Bus Communications

COM

SA Bus Signal Reference and 15

VDC Common

SA BUS

SA PWR

15 VDC Supply Power for Devices

on the SA Bus
(Maximum total current draw for SA

Bus is 240 mA.)

0.6 mm (22 AWG)

stranded, 4-wire (2

twisted-pairs), shielded

cable recommended.

Note:

The + and - wire

are one twisted pair,

and the COM and SA

PWR are the second

twisted pair of wires.

FC BUS

(Port)

FC BUS

RJ-12 6-Position Modular Connector

provides:
FC Bus Communications
FC Bus Signal Reference and 15

VDC Common
15 VDC, 180 mA, Power for

Bluetooth Commissioning

Converter

Bluetooth Commissioning

Converter retractable

cable or 24 AWG 3-pair CAT

3 cable or above.

Sensor

(Port)

SENSOR

RJ-12 6-Position Modular Connector

provides:
SA Bus Communications
SA Bus Signal Reference and 15

VDC Common
15 VDC Power for devices on the SA

bus and Bluetooth Commissioning

Converter

24 AWG 3-pair CAT3 cable

<30.5 m (100 ft)

HOT

24 VAC Power Supply - Hot

Supply 20–30 VAC (Nominal 24 VAC)

24~

COM

24 VAC Power Supply Common

(Isolated from all other Common

terminals on controller)
14 VA

0.8 mm to 1.0 mm
(18 AWG) 2-wire

PCA3613 Advanced Application Programmable Controller Installation Instructions

Содержание PCA3613































Результаты поиска

Содержание PCA3613

Отзывы:

Похожие инструкции для PCA3613

Бренды по названию

Популярные бренды

Johnson Controls PCA3613, Руководство по установке

Результаты поиска

Содержание PCA3613

Отзывы:

Похожие инструкции для PCA3613

Бренды по названию

Популярные бренды