manualshive.com logo in svg

Johnson Controls Kantech tyco ioSmart, Руководство по установке

Поделиться
Скачать
Johnson Controls Kantech tyco ioSmart Скачать руководство пользователя страница 38

Configuring the reader

This section describes how to configure the reader by short circuiting the wires on the terminal, and

how to configure the reader using your Kantech smart card.

Configuring the reader using the terminals

Use this section to configure the reader using the terminals.

Note: 

If RS-485 communication is not detected when you turn on the reader, it transmits

Wiegand format according to its configuration.

Factory default (SSF transmission format)

Figure 18: Factory default terminal block shorting diagram

SSF is the factory default configuration.

Important: 

Forcing the reader to factory default deletes all custom settings from the reader

and defaults BLE credential data. If you factory default a panel-less reader, you may need to

contact technical support to reset it.

To return the reader to the factory default configuration, complete the following steps:

1. Short circuit together the D0 and BUZ terminals.
2. Short circuit together the D1 and LED terminals.
3. Apply power to the reader.

A simultaneous sequence of four beeps and flashes, four times, indicates a successful return to

the SSF transmission format.
A sequence of rapid beeps and flashes for 4 seconds indicates that the device has not returned

to the SSF transmission format.

ioSmart Card Reader Installation Guide

38

Содержание Kantech tyco ioSmart















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды