Johnson Controls J ZT Series Скачать руководство пользователя | Manualshive

Страница: 31 / 66

background image

5370597-JIM-D-1019

Johnson Controls Ducted Systems

31

If the demand for cooling from the space/return is satisfied, the
economizer output will modulate to minimum position and the
compressor outputs will be de-energized as long as their
minimum run timers have expired.

Power Exhaust

Setpoints

a. Economizer Enable ON

b. Power Exhaust Enable ON

c. Modulating Power Exhaust OFF

d. Exhaust VFD Installed OFF

e. Building Pressure Sensor Enabled OFF

f. Econo Damper Position For Exh Fan ON Percent

g. Econo Damper Position For Exh Fan OFF Percent

Inputs

No inputs are present for non-modulating power exhaust.

Outputs

a. 2-10 VDC from ECON on Economizer Expansion module

b. 24 VAC from EX-FAN to energize exhaust fan on

Economizer Expansion module

Operation

Operation details include:

a. Compares economizer output to the Economizer Damper

Position For Exhaust Fan On and OFF.

b. Energizes exhaust fan when economizer output is above

Economizer Damper Position For Exhaust Fan On.

c. De-energizes exhaust fan when economizer output is

below the Economizer Damper Position for Exhaust Fan
OFF

«
...
29
30
31
32
33
...
»

Содержание J ZT Series



































































Отзывы:

Нет отзывов

Похожие инструкции для J ZT Series

Бренд: Panasonic Страницы: 108

Бренд: Panasonic Страницы: 140

Бренд: Galletti Страницы: 20

Бренд: Parker Страницы: 36

Бренд: Aircommand Страницы: 22

Бренд: Garrison Страницы: 26

Бренд: Silent Night Страницы: 12

Бренд: Uberhaus Страницы: 24

Бренд: Camfil Страницы: 63

Бренд: ClimateRight Страницы: 10

Бренд: Seifert Страницы: 23

Бренд: IP Enclosures Страницы: 16

Бренд: Ozeanos Страницы: 24

Бренд: Rheem Страницы: 37

Бренд: SANITY SYSTEM Страницы: 36

Бренд: Carrier Страницы: 68

Бренд: Daikin Страницы: 160

Бренд: Daikin Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды