Johnson Controls Intelligent Fire Integrator NION-16C48M Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 40

background image

JNISCAB-3 NION Enclosure Installation

Description and Installation

13

NION-16C48M Installation & Operation Manual - P/N: 53347:Rev: A1 5/5/09

2.3 JNISCAB-3 NION Enclosure Installation

The JNISCAB-3 enclosure has a locking door and mounting hardware for the NION-16C48M
assembly (motherboard, terminal boards and network transceiver), UL listed power supply,
transformer and batteries. These must be ordered separately.

Follow the steps below to install the NION-16C48M and power supply into the JNISCAB-3
enclosure. This enclosure is provided with door and key lock.

Mounting the enclosure to its wall position

Step 1. Use the provided key to unlock the enclosure cover.
Step 2. Remove the enclosure cover.
Step 3. Mount the enclosure to the wall. Refer to the enclosure mounting hole layout below.
Step 4. Mount the power supply and transformer to the standoffs in the back of the cabinet using

the provided hardware.

Step 5. Mount the NION-16C48M motherboard to the mounting rails in the same manner.

Figure 2.4 JNISCAB-3 Mounting Hole Layout

Distances can vary between the NION and monitored equipment, but the maximum wire resistance
must not exceed 500 ohms. The type of hardware used is at the discretion of the installer but must
be in accordance with local code requirements. The NION is designed to be installed on a wall
within 20 feet of the panel in the same room.

2"

11.5"

14.5"

.25"

Dia.

2 Places

12.5"

.50"

.25"

.50"

«
...
11
12
13
14
15
...
»

Содержание Intelligent Fire Integrator NION-16C48M









































Отзывы:

Нет отзывов

Похожие инструкции для Intelligent Fire Integrator NION-16C48M

Бренд: Fandis Страницы: 8

Бренд: SAFERA Страницы: 15

Бренд: VHD Страницы: 2

Бренд: Cerdi Страницы: 24

Бренд: RainWater Harvesting Страницы: 3

Бренд: Leister Страницы: 14

Бренд: Parweld Страницы: 20

Бренд: Weir Страницы: 42

Бренд: dallmeier Страницы: 40

Бренд: Ideal Security Страницы: 4

Бренд: Zamel Страницы: 2

Бренд: M-system Страницы: 2

Бренд: Quest Engineering Страницы: 12

Бренд: Daikin Страницы: 36

Бренд: Nellcor Страницы: 18

Бренд: omisa Страницы: 44

Бренд: Bticino Страницы: 2

POWER CUT 60HFIII

Бренд: Mweld Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды