Johnson Controls FX-PCV18 Series Скачать руководство пользователя страница 1

Страница: 1 / 30

FX-PCV1826/1832 Programmable VAV Box

Controller Installation Instructions

Applications

FX-PCV1826 controllers are well-suited for commercial zoning applications and can be used

for pressure dependent VAV box applications where no differential pressure tranduser (DPT) is

required.

Note:

At Controller Configuration Tool (CCT) 13.0 or later, using Release Mode 10.1, the PCV18

Series controllers can be configured as either N2 devices or as standard BACnet

MS/TP

devices. This ability provides a potential cost-effective protocol upgrade path for existing

customers and should be considered when you install the controller.

Important:

When you receive an FX-PCV18 Series controller from the factory or upgrade the

firmware or main code, the controller defaults to using the MS/TP communications protocol.

The Load Summary screen of CCT shows the connection as

Wired Field Bus

, indicating that

the MS/TP protocol is in use. If you have an N2 application, the Load Summary screen indicates

that you need to switch the communications protocol to N2.

These FX-PCV controllers feature an integral digital pressure sensor (FX-PCV1832 model only), a

damper actuator, and a 32-bit microprocessor. The controller's small package size facilitates quick

field installation and efficient use of space for field replacements, while still enabling precision

control performance.

Note:

Connecting an FX-PCX to the FX-PCV via the SA Bus connection is not supported.

North American Emissions Compliance

United States

This equipment has been tested and found to comply with the limits for a Class A digital device

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when this equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instruction manual, may cause harmful interference to

radio communications. Operation of this equipment in a residential area may cause harmful

interference, in which case the users will be required to correct the interference at their own

expense.

Canada

This Class (A) digital apparatus meets all the requirements of the Canadian Interference-Causing

Equipment Regulations.
Cet appareil numérique de la Classe (A) respecte toutes les exigences du Règlement sur le

matériel brouilleur du Canada.

Installation

Observe these guidelines when installing an FX-PCV18 Series controller:

Part No. 24-10143-381 Rev H
2019-03-22

(barcode for factory use only)

FX-PCV1826-1, FX-PCV1832-1

*2410143381H*

Содержание FX-PCV18 Series































Результаты поиска

Содержание FX-PCV18 Series

Отзывы:

Похожие инструкции для FX-PCV18 Series

Бренды по названию

Популярные бренды

Johnson Controls FX-PCV18 Series, Руководство по установке

Результаты поиска

Содержание FX-PCV18 Series

Отзывы:

Похожие инструкции для FX-PCV18 Series

Бренды по названию

Популярные бренды