Johnson Controls FCP-NA-701-L Скачать руководство пользователя страница 27

Страница: 27 / 28

Table 10: FCP non-programmable and programmable FCU or PTAC Thermostats technical

specifications

Specification

Description

Dimensions H x W x D

3.27 in. x 3.94 in. x 0.98 in. (83 mm x 100 mm x 25 mm)

Shipping weight

Product with packing and accessories: 10.1 oz (285 g)

Thermostat only: 4.9 oz (138 g)

Trim plate: 1.2 oz (33 g)

Compliance

ETL/cETL Listed, Mexico NOM

CONFORMS TO UL STD. 60730-1 & 60730-2-9

CERTIFIED TO CSA STD. E60730-1 & E60730-2-9

The performance specifications are nominal and conform to acceptable industry standards. For

application at conditions beyond these specifications, consult the local Johnson Controls office. Johnson

Controls shall not be liable for damages resulting from misapplication or misuse of its products.

Product warranty

This product is covered by a limited warranty, details of which can be found at

www.johnsoncontrols.com/buildingswarranty

Patents

Patents:

https://jcipat.com

Contact information

Contact your local branch office:

www.johnsoncontrols.com/locations

Contact Johnson Controls:

www.johnsoncontrols.com/contact-us

FCP Non-Programmable and Programmable Fan Coil or PTAC Thermostat Largo User Guide

Содержание FCP-NA-701-L




























Результаты поиска

Содержание FCP-NA-701-L

Отзывы:

Похожие инструкции для FCP-NA-701-L

Бренды по названию

Популярные бренды

Johnson Controls FCP-NA-701-L, Руководство пользователя

Результаты поиска

Содержание FCP-NA-701-L

Отзывы:

Похожие инструкции для FCP-NA-701-L

Бренды по названию

Популярные бренды