Johnson Controls FCP-NA-701-L Скачать руководство пользователя страница 20

Страница: 20 / 28

Table 8: Default schedule

6:00 A.M.

Heat: 70°F

Cool: 74°F

6:00 A.M.

Heat: 70°F

Cool: 74°F

6:00 A.M.

Heat: 70°F

Cool: 74°F

6:00 A.M.

Heat: 70°F

Cool: 74°F

8:00 A.M.

Heat: 70°F

Cool: 74°F

10:00 A.M.

Heat: 70°F

Cool: 74°F

8:00 A.M.

Heat: 62°F

Cool: 82°F

8:00 A.M.

Heat: 62°F

Cool: 82°F

8:00 A.M.

Heat: 62°F

Cool: 82°F

12:00 P.M.

Heat: 70°F

Cool: 74°F

6:00 P.M.

Heat: 62°F

Cool: 75°F

12:00 P.M.

Heat: 70°F

Cool: 74°F

12:00 P.M.

Heat: 70°F

Cool: 74°F

6:00 P.M.

Heat: 70°F

Cool: 74°F

10:00 P.M.

Heat: 62°F

Cool: 75°F

2:00 P.M.

Heat: 62°F

Cool: 82°F

6:00 P.M.

Heat: 70°F

Cool: 74°F

10:00 P.M.

Heat: 62°F

Cool: 75°F

6:00 P.M.

Heat: 70°F

Cool: 74°F

10:00 P.M.

Heat: 62°F

Cool: 75°F

10:00 P.M.

Heat: 62°F

Cool: 75°F

Auto daylight savings

About this task:

Auto daylight savings is turned on by default and only applies when the

thermostat is in programmable mode. When auto daylight savings is on the clock automatically

changes on the following days:

• The second Sunday in March, from 02:00 to 03:00
• The first Sunday in November, from 02:00 to 01:00

To turn off the auto daylight savings, complete the following steps:

1. Press

Mode

to set the thermostat to OFF mode.

2. Press and hold

Mode

and

Fan

for 5 seconds to access the advanced settings menu.

3. Press

to navigate to UP, then press

Mode

to enter the menu.

4. Press

Mode

to navigate to 09.

5. Use the

and

Down

buttons to change the auto daylight savings to OFF, then press

Mode

to confirm the change.

Unoccupied mode

The dry-contact input can trigger the unoccupied mode. You can also configure the polarity of the

dry contact to normally open or normally closed in the IS menu.
Alternatively, you can manually enable or disable the unoccupied mode. Press and hold

Mode

for

5 seconds to manually enable or disable the unoccupied mode.
You can set the unoccupied action to setpoint change or off mode. When you select setpoint

change, the thermostat uses the unoccupied setpoints when the unoccupied mode is triggered.

When you select off mode, the thermostat switches to off mode when the unoccupied mode is

triggered.

FCP Non-Programmable and Programmable Fan Coil or PTAC Thermostat Largo User Guide

Содержание FCP-NA-701-L




























Результаты поиска

Содержание FCP-NA-701-L

Отзывы:

Похожие инструкции для FCP-NA-701-L

Бренды по названию

Популярные бренды

Johnson Controls FCP-NA-701-L, Руководство пользователя

Результаты поиска

Содержание FCP-NA-701-L

Отзывы:

Похожие инструкции для FCP-NA-701-L

Бренды по названию

Популярные бренды