Johnson Controls Bentel Security tyco ABS128M50, Руководство по установке

Страница: 70 / 132

n
Event Description
This section describes the conditions that generate,
and terminate each event.
Zone Events Table 11 shows Zone events associated
with Zone alarm and Zone Tamper events.
A Zone event can be restored to standby by:
Ø
changing the status (Armed/Disarmed) of a Partition
the Zone is associated with;
Ø
running Alarm Reset from a Keypad (the entered
User PIN and Keypad must be jointly enabled on a
Partition the Zone is associated with);
Ø
running Alarm Stop from the Keypad (the entered
User PIN and Keypad must be jointly enabled on a
Partition the Zone is associated with);
Ø
Using a valid Key on a Reader (both Key and Reader
must be jointly Enabled on a Partition the Zone is as-
sociated with).
Partition Events Table 12 shows the Partition Events.
The Partition Events encase the Zone Events (Fire,
24h, Burglar, etc.). Each Zone event will in turn gener-
ate a Partition event (on the Partition the Zone is associ-
ated with). The Partition event will not terminate until all
the Zone events end.
Partition Events can be restored to standby by:
Ø
changing the Partition status (Armed/Disarmed);
Ø
running Alarm Reset from a Keypad (the entered
User PIN and Keypad must be jointly enabled on the
Partition concerned);
Ø
running Alarm Stop from the Keypad (the entered
User PIN and Keypad must be jointly enabled on the
Partition concerned);
Ø
Using a valid Key on a Reader (both Key and Reader
must be jointly enabled on the Partition concerned).
System Events These are Control Panel-generated
warnings (e.g. Power Failure).
System Events can be restored to standby by:
Ø
running Alarm Reset from a Keypad;
Ø
running Alarm Stop from a Keypad;
Ø
using a Key on a Reader.
Spot Events Spot events, such as Recognized User
PIN on Keypad , are instant. Therefore, any action under-
taken on termination would serve no purpose. Therefore:
Ø
Bistable Outputs CANNOT be associated with Spot
Events;
Ø
Dialler and Digital Communicator Actions CANNOT
be associated with restoral of Spot Events.
n
Remote Command Events
3
In order comply with EN50131 Grade 3 standards,
the “Remote Command” Events must NOT be con-
trolled by SMS.
These events (Table 16) occur and end when the con-
trol panel receives an SMS with the following format:
#ABS#E#<PIN>#<ON|OFF>#<Command String>#<Text>
Ø
PIN : a valid User PIN with the SMS option enabled
(See the
Users
>
Codes and Options
option group).
Ø
ON|OFF : ON makes the event occurs; OFF ends the
event.
Ø
Command String : the string entered in the Com-
mand String option (NOT case-sensitive).
Ø
Text : an additional text ignored by the control panel
that can be used by the user to assign a description
to the command’s SMS.
+
The event occurs or ends ONLY if the PIN and the
event share at least one Partition (see
Partitions ).
+
The user can disable his own PIN by an SMS mes-
sage, as described in the USER MANUAL.
The control panel sends confirmation by SMS when the op-
eration has ended successfully (see the USER MANUAL).
+
These events can also be controlled using an
iPhone or Android smartphone via the
ABSOLUTA
App and via an ABSOLUTA M-Touch keypad (see
“USER MANUAL > Touch Keypad Operations >
Scenarios”).
Command String Type the string that needs to be
sent in order for the event occurs or end (NOT
case-sensitive).
The string may consist of up to 16 characters.
Default: empty.
Partitions If disabled, the respective Partition is NOT
assigned to the event.
If ENABLED (default), the respective Partition is as-
signed to the event.
70 Expandable Hybrid Control Panel